1
00:00:09,633 --> 00:00:11,133
Hi, my name is Joel Kenyon

2
00:00:11,133 --> 00:00:12,566
and I’m a product manager
here at Olympus.

3
00:00:12,566 --> 00:00:13,833
Today I’m going to show you

4
00:00:13,833 --> 00:00:16,066
how to install a Hot Heel
and Weld Mask accessory

5
00:00:16,066 --> 00:00:17,700
on your Vanta analyzer.

6
00:00:17,700 --> 00:00:19,400
The Hot Heel is used
to maintain a gap

7
00:00:19,400 --> 00:00:21,000
between the window and sample

8
00:00:21,000 --> 00:00:23,733
to minimize heat transfer
when testing hot objects,

9
00:00:23,733 --> 00:00:25,033
and the Weld Mask is used

10
00:00:25,033 --> 00:00:27,033
to focus on a narrow
strip of material,

11
00:00:27,033 --> 00:00:28,433
like a weld.

12
00:00:28,433 --> 00:00:29,633
I’m only going to demonstrate

13
00:00:29,633 --> 00:00:31,166
using the Hot Heel but the process

14
00:00:31,166 --> 00:00:33,200
is the same for the Weld Mask.

15
00:00:33,200 --> 00:00:34,933
Start by making sure

16
00:00:34,933 --> 00:00:37,466
that your Vanta is powered down.

17
00:00:37,466 --> 00:00:38,933
And remove the Vanta faceplate

18
00:00:38,933 --> 00:00:40,933
by pressing the large round button

19
00:00:40,933 --> 00:00:45,066
on the underside of the probe head.

20
00:00:45,066 --> 00:00:47,200
Use the Allen® wrench
supplied with the Hot Heel

21
00:00:47,200 --> 00:00:48,733
to remove the screw holding the tether

22
00:00:48,733 --> 00:00:50,200
to the faceplate.

23
00:00:50,200 --> 00:00:55,766
Be careful not to lose
the screw or the washer.

24
00:00:55,766 --> 00:00:58,066
Place the analyzer window
on the gasket

25
00:00:58,066 --> 00:01:03,633
so that the rounded edges match up.

26
00:01:03,633 --> 00:01:05,733
Gently press around
the edges of the window

27
00:01:05,733 --> 00:01:08,400
to adhere the window to the gasket.

28
00:01:08,400 --> 00:01:10,866
Re-attach the tether
to the Hot Heel faceplate

29
00:01:10,866 --> 00:01:18,366
and hang it off to the side.

30
00:01:18,366 --> 00:01:20,633
Place the window
and gasket on the analyzer

31
00:01:20,633 --> 00:01:24,033
with the window side down.

32
00:01:24,033 --> 00:01:26,100
Snap the Hot Heel
faceplate into place

33
00:01:26,100 --> 00:01:28,500
by sliding the notch
at the top of the faceplate

34
00:01:28,500 --> 00:01:30,633
into the notch
at the top of the probe head

35
00:01:30,633 --> 00:01:31,933
and gently press the bottom

36
00:01:31,933 --> 00:01:34,166
until you feel it click into place.

37
00:01:34,166 --> 00:01:35,466
And there you have it.

38
00:01:35,466 --> 00:01:36,933
You’re now ready to test hot samples

39
00:01:36,933 --> 00:01:38,733
and welds with your Vanta analyzer.

40
00:01:38,733 --> 00:01:40,600
Thanks for watching.