1
00:00:09,676 --> 00:00:11,378
Olympus is proud to introduce

2
00:00:11,378 --> 00:00:13,815
two new dual element transducers

3
00:00:13,815 --> 00:00:16,083
for use with the 27MG,

4
00:00:16,083 --> 00:00:20,655
45MG, and 38DL PLUS
ultrasonic thickness gages.

5
00:00:20,655 --> 00:00:24,691
The D7912 and D7913 are 10 MHz

6
00:00:24,691 --> 00:00:26,493
dual element transducers

7
00:00:26,493 --> 00:00:32,233
with a small tip diameter
of 0.295 in., or 7 mm.

8
00:00:32,233 --> 00:00:34,535
They are designed for making
thickness measurements

9
00:00:34,535 --> 00:00:37,371
on thin walled, small
diameter tubes and pipes

10
00:00:37,371 --> 00:00:41,175
at temperatures below
125 degrees Fahrenheit

11
00:00:41,175 --> 00:00:43,811
or 50 degrees Celsius.

12
00:00:43,811 --> 00:00:46,546
The thickness measurement
range for these transducers

13
00:00:46,546 --> 00:00:50,218
is approximately twenty thousands
of an inch to one inch

14
00:00:50,218 --> 00:00:52,653
or zero point five millimeters

15
00:00:52,653 --> 00:00:54,721
to twentyfive point four millimeters

16
00:00:54,721 --> 00:00:57,758
depending on the material
and applications.

17
00:00:57,758 --> 00:00:59,826
Use of the instrument’s
gain adjustment

18
00:00:59,826 --> 00:01:02,796
may be required to achieve
the full thickness range.

19
00:01:02,796 --> 00:01:06,566
The D7913 is a right angle transducer

20
00:01:06,566 --> 00:01:07,935
with a potted cable

21
00:01:07,935 --> 00:01:10,271
and rubber over molded strain relief.

22
00:01:10,271 --> 00:01:12,306
This transducer is great
for applications

23
00:01:12,306 --> 00:01:14,708
with limited height requirements.

24
00:01:14,708 --> 00:01:17,545
The D7912 is a straight version

25
00:01:17,545 --> 00:01:20,248
with a potted cable and
over molded bell housing

26
00:01:20,248 --> 00:01:22,816
strain relief.

27
00:01:22,816 --> 00:01:26,186
Both the D7912 and D7913

28
00:01:26,186 --> 00:01:28,623
are constructed with
a stainless steel case

29
00:01:28,623 --> 00:01:31,125
for excellent wear resistance.

30
00:01:31,125 --> 00:01:33,193
These dual element
transducers are designed

31
00:01:33,193 --> 00:01:36,063
to meet the center
frequency specification

32
00:01:36,063 --> 00:01:39,633
of EN15317.

33
00:01:39,633 --> 00:01:42,636
The D7912 and the D7913

34
00:01:42,636 --> 00:01:46,373
Along with our lower cost 5 MHz D7910

35
00:01:46,373 --> 00:01:48,743
Are great additions to
the Olympus line

36
00:01:48,743 --> 00:01:51,778
of high quality corrosion thickness
gage transducers.

37
00:01:51,778 --> 00:01:55,383
For more information, contact your
local sales representative

38
00:01:55,383 --> 00:02:01,355
or visit our website at
www.olympus-ims.com.