Evident LogoOlympus Logo
Olympus Industrial Resources
Application Notes
Back to Resources

Measuring Nodularity in Cast Iron Using Ultrasonic Testing


This application note explains how to measure the degree of nodularity in cast iron and distinguish nodular iron from gray iron. Learn about the ultrasonic inspection equipment and techniques used to perform nondestructive nodularity testing in cast iron.


Cast Iron Production

Carbon in the form of graphite is often used as an additive in the production of cast iron, amounting to 2 to 4 percent by weight or 6 to 10 percent by volume in typical castings. The microstructure of graphite within cast iron has major effects on the casting’s mechanical properties. When graphite arranges itself as thin flakes, the result is gray iron, which is hard and brittle. When graphite takes the form of spherical nodules, the result is nodular iron, which is soft and malleable.

Both gray and nodular iron are made by mixing carbon, silicon, and other additives into molten iron. Often, some of this mixing is done in the final mold. If the mixing is non-uniform or the casting process has other imperfections, the casting might have variations in nodularity or have pockets of gray iron within a nodular iron casting. These variations will significantly change the mechanical properties of the metal, so foundries need to check nodular iron for uniformity. It is important that the distribution of graphite in the casting is uniform and that graphite inclusions are in the right form (nodules rather than flakes).

Microscopic examination and tensile strength tests are effective methods for checking nodularity. Another option is ultrasonic testing, which can measure the distinct sound velocities of nodular and gray iron. This method is preferred because it provides a fast, nondestructive evaluation of a casting.

Ultrasonic Inspection Equipment Used for Nondestructive Nodularity Testing in Cast Iron

Nondestructive nodularity testing can be performed with any ultrasonic instrument that can measure sound velocity, which includes thickness gauges, flaw detectors, and pulser-receivers. For dedicated velocity measurement, all Olympus precision thickness gauges can provide a direct readout of sound velocity in cast iron and other materials based on an entered thickness calibration. These include the 38DL PLUS™ gauge and the 45MG gauge with Single Element software. For thicknesses greater than approximately 25 mm (1 in.), the High Penetration software option for the gauges is often recommended.

To perform a nodularity test using a thickness gauge, simply press a key to enter the thickness data. The sound velocity calculates automatically from this entered thickness and the measured pulse transit time. Use a high/low alarm function to identify out-of-tolerance conditions. Pair the gauge with a transducer appropriate for the thickness range being measured. One common choice is an M1036 2.25 MHz contact transducer. Velocity measurement accuracy is typically on the order of one tenth of one percent.

The 72DL PLUS™ gauge offers a larger touch-screen display and a higher measurement update rate (up to 2 KHz) than the 38DL PLUS and 45MG gauges. This precision thickness gauge also offers higher time measurement resolution, which leads to more precise sound velocity calculations. In addition, the 72DL PLUS gauge offers greater connectivity via wireless and wired communication options, which is ideal for system integration.

Any of the EPOCH™ flaw detectors, such as the EPOCH 650 and EPOCH 6LT instruments, can be used in a similar way to measure an unknown velocity. With the flaw detector calibrated for an appropriate low-frequency transducer, obtain a back wall echo from a section of known thickness and perform a velocity calibration, which will calculate material velocity based on the detected echoes.

Ultrasonic Testing Procedure for Measuring Nodularity in Cast Iron

There is a consistent difference in sound velocity between pure iron, nodular cast iron, and gray cast iron. Typically, pure elemental iron has a velocity of approximately 0.232 in./µS (5.9 mm/µS), nodular iron has a velocity of approximately 0.222 in./µS (5.6 mm/µS), and gray iron has a velocity of approximately 0.192 in./µS (4.8 mm/µS). The exact velocities for your application will vary depending on alloy composition, grain structure, and other process variables. Always verify the exact velocities based on calibration standards for the test material.

We recommend that you establish your own chart of velocity vs. percent of nodularity for each application. Published research indicates that the relationship between velocity and percent of nodularity is not linear1. However, it is possible to have a substantial difference in sound velocity between two otherwise identical castings containing the same percentage of graphite—one with the graphite in flake form (gray iron) and the other with spherical graphite (nodular iron).

Note that measurement of sound velocity requires that the thickness of the test piece is known. Typically, inspectors perform ultrasonic nodularity testing at points on a casting where the thickness can be measured mechanically using a micrometer or caliper. Accurate velocity measurement is impossible if the thickness at the test point is unknown.

Another application that can be detected ultrasonically is the presence of gray iron inclusions in a nodular iron casting. The sound velocity of gray iron is lower than that of nodular iron, so the pulse transit time through a casting containing a gray iron inclusion is longer than a casting made entirely of nodular iron. The measured sound velocity is also lower. Given the complex variables affecting actual castings, we recommended that you set up the test based on calibration standards of known composition. However, a localized drop in sound velocity in a nodular iron casting is generally a sign of a potential issue.


Note: Nodularity and other aspects of graphite microstructure in cast iron can also be analyzed microscopically using interpretive software developed by Olympus. Find more details here (https://www.olympus-ims.com/en/applications/cast-iron-analysis/).

References

  1. ASM International, Metals Handbook, Volume 17, Nondestructive Evaluation and Quality Control, Metals Park, Ohio 1989 (Ninth Edition), pp. 531-535.
  2. Nondestructive Characterization of Cast Irons by Ultrasonic Method, http://www.ndt.net/article/wcndt00/papers/idn035/idn035.htm
Olympus IMS

Products Used for This Application

The 72DL PLUS™ advanced ultrasonic thickness gauge delivers precision thickness measurements at high speed in a portable, easy-to-use device. Compatible with single element transducers up to 125 MHz, this innovative instrument is ideally suited to measure the thickness of ultra-thin materials, including multilayer paint, coatings, and plastic. It can simultaneously display the thickness of up to 6 layers.

The EPOCH 6LT portable ultrasonic flaw detector is optimized for one-handed operation and delivers excellent performance in rope access and high-portability applications. Lightweight with an ergonomic design, the instrument fits securely in a user’s hand or can be strapped to the leg for rope access applications.
The EPOCH 650 is a conventional ultrasonic flaw detector with excellent inspection performance and usability for a wide variety of applications. This intuitive, rugged instrument is a continuation of the popular EPOCH 600 flaw detector with additional capabilities.
The handheld 45MG ultrasonic thickness gauge is packed with measurement features and software options. This unique instrument is compatible with the complete range of Olympus dual element and single element transducers, making this gauge an all-in-one solution for virtually every thickness gauge application.
The 38DL PLUS is an advanced ultrasonic thickness gauge. Uses dual element transducer for internal corrosion applications, and has features that include THRU-COAT technology and echo-to-echo. Uses single element transducers for very precise thickness measurements of thin, very thick, or multilayer materials.
Sorry, this page is not available in your country
Let us know what you're looking for by filling out the form below.
Sorry, this page is not available in your country